Rigol DG5000 Series Manuel d'utilisateur Page 121
- Page / 224
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Chapter 6 Frequency Sweep Output RIGOL
User’s Guide for DG5000
6-9
The generator will renewedly sweep and output with the specified “start frequency”
once the End Hold is changed.
Sweep Trigger Source
The Sweep trigger source could be internal, external or manual source. The generator
will generate a sweep output when a trigger signal is received and then wait for the
next trigger.
When Sweep is enabled, press Source to select “Internal”, “External” or “Manual”.
The default is “Internal”.
1. Internal Trigger
The generator outputs continuous sweep waveform. The trigger period is
determined by the specified sweep time, return time, start hold and stop hold
times.
2. External Trigger
The generator accepts the external trigger signal from the ExtTrig connector at
the rear panel. A sweep will be generated once the connector gets a TTL pulse
with specified polarity. To set the TTL pulse polarity, press SlopeIn to select
“Leading” or “Trailing”. The default is “Leading”.
3. Manual Trigger
A sweep will be generated once you press the Manual for dual-channel model or
you press the Trigger key at the front panel for single channel model.
- User’s Guide 1
- Guaranty and Declaration 3
- Safety Requirement 4
- Handling Safety 6
- Safety Terms and Symbols 7
- RIGOL 10
- User’s Guide for DG5000 10
- General Care and Cleaning 12
- Environmental Considerations 13
- DG5000 Series Overview 14
- RIGOL 15
- Document Overview 16
- Chapter 14 Appendix 17
- Contents 18
- Contents RIGOL 19
- RIGOL Contents 20
- Chapter 1 Quick Start 25
- General Inspection 26
- Handle Adjustment 27
- Appearance and Dimensions 28
- Front Panel 29
- RIGOL Chapter 1 Quick Start 30
- Rear Panel 35
- Power on the Generator 38
- User Interface 39
- To Rack Mount the Instrument 41
- Installation Tool 42
- Installation Procedures 43
- To Use the Security Lock 46
- To Use the Built-In Help 47
- To Output Sine Waveform 50
- To Output Square Waveform 53
- Symmetry 54
- =t/T*100% 54
- To Output Pulse Waveform 55
- CH1 Output 56
- CH2 Output 56
- Restore Delay 57
- To Output Noise Waveform 59
- Align Phase 60
- To Enable Arbitrary Waveform 62
- Waveform” 63
- Output Mode 64
- Play Mode 65
- To Select Arbitrary Waveform 66
- Stored Waveform 67
- Volatile Waveform 67
- Programming Guide 70
- Edit Points 71
- Edit Block 73
- To Edit Arbitrary Waveform 75
- Amplitude Modulation (AM) 78
- To Set Modulation Depth 80
- Frequency Modulation (FM) 81
- To Set Frequency Deviation 83
- Phase Modulation (PM) 84
- To Set Phase Deviation 86
- Amplitude Shift Keying (ASK) 87
- To Set ASK Rate 88
- To Set Modulating Amplitude 89
- To Set Modulating Polarity 89
- Frequency Shift Keying (FSK) 90
- To Set Carrier Frequency 91
- To Set FSK Rate 92
- To Set Hop Frequency 92
- Phase Shift Keying (PSK) 93
- To Set PSK Rate 94
- To Set Modulating Phase 95
- Pulse Width Modulation (PWM) 96
- IQ Modulation Overview 100
- To Select IQ Modulation 101
- To Select Code Pattern 103
- User-defined Code Pattern 104
- Save/Read User’s Data 105
- Application of User’s Data 105
- To Set Code Rate 106
- IQ Mapping 107
- User’s Guide for DG5000 109
- To Enable Frequency Sweep 114
- Sweep Type 116
- Log Sweep 117
- Step Sweep 118
- Sweep Time 119
- Return Time 119
- Mark Frequency 119
- Start Hold 120
- End Hold 120
- Sweep Trigger Source 121
- Sweep Trigger Output 122
- Chapter 7 Burst Output 123
- To Enable Burst Mode 124
- Burst Type 124
- Infinite Burst 125
- Gated Burst 126
- Burst Phase 127
- Burst Period 127
- Gated Polarity 127
- Burst Delay 128
- Burst Trigger Source 128
- Burst Trigger Output 129
- Chapter 8 FH Output (Option) 131
- FH Overview 132
- To Enable FH Function 133
- To Select Carrier Waveform 134
- FH Switch 134
- FH Interval 134
- Start Point 135
- Display Type 135
- To Load Map 136
- To Edit Map 137
- To Edit List 138
- To Create List 138
- FH Sequence 139
- To Save FH Map 140
- Chapter 9 Store and Recall 141
- Storage System Overview 142
- To Select File Type 143
- To Select Browser Type 144
- To Save a File 144
- To Recall a File 147
- To Copy a File 147
- To Paste a File 148
- To Delete a File or Folder 148
- To Create a New Folder 149
- Format the Local Disk 149
- Seamlessly Interconnection 150
- Advanced Operation Overview 152
- Channel Setting 153
- Sync Polarity 155
- Output Polarity 155
- Resistance Setting 156
- Range Setting 156
- Attenuation Setting 157
- Enable Freq Hop Function 157
- Channel Coupling 158
- Channel Copy 160
- System Setting 161
- Language 162
- Power On Setting 162
- Restore Default 162
- Display Setting 167
- Beep Setting 168
- Screen Saver Setting 168
- Clock Source Setting 169
- User-defined Shortcut 170
- System Information 170
- Test Calibration 172
- Protocol Setting 180
- To Set the Code Pattern 183
- User Data Editing 184
- Trigger Setting 188
- To Install the Option 189
- To Set GPIB Address 190
- LAN Setting 190
- IP Configure Mode 191
- Network Status 191
- MAC Address 191
- VISA Descriptor 191
- To Set USB Device Type 195
- Chapter 11 Remote Control 197
- Remote Control Via USB 198
- Remote Control Via LAN 200
- Remote Control Via GPIB 203
- Chapter 12 Troubleshooting 205
- Chapter 13 Specifications 209
- Appendix D: Warranty 222
- Index RIGOL 223
- RIGOL Index 224
Produits connexes et manuels pour Générateurs Rigol DG5000 Series
(190 pages)
Générateurs Rigol DP832A Manuel d'utilisateur
(146 pages)
(146 pages)
Générateurs Rigol DP832 Manuel d'utilisateur
(144 pages)
(144 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.078 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels